复制
收藏
提问
简洁
基于stm32的按键驱动程序,写出控制led工作的源代码key1短按红灯亮,key2长按绿灯亮,key3双击蓝灯亮。
3月前
全网
文档
学术
百科
知识库
回答简洁模式
深入研究一些
基于STM32的按键驱动程序,控制LED工作的源代码需要包括按键初始化、LED初始化、中断服务以及主控逻辑。以下是一个简化的示例代码,用于实现key1短按红灯亮,key2长按绿灯亮,key3双击蓝灯亮的功能。请注意,这只是一个示例,实际应用中可能需要根据具体的硬件配置和需求进行调整。
#include "stm32f10x.h"
// 假设LED连接到GPIOA的PA0、PA1和PA2
#define LED_RED_PIN GPIO_Pin_0
#define LED_GREEN_PIN GPIO_Pin_1
#define LED_BLUE_PIN GPIO_Pin_2
#define LED_GPIO_PORT GPIOA
#define LED_GPIO_CLK RCC_APB2Periph_GPIOA
// 假设KEY1、KEY2和KEY3分别连接到GPIOB的PB0、PB1和PB2
#define KEY1_PIN GPIO_Pin_0
#define KEY2_PIN GPIO_Pin_1
#define KEY3_PIN GPIO_Pin_2
#define KEY_GPIO_PORT GPIOB
#define KEY_GPIO_CLK RCC_APB2Periph_GPIOB
// 按键去抖动时间,单位为ms
#define DEBOUNCE_TIME 50
// 长按和双击的时间阈值,单位为ms
#define LONG_PRESS_TIME 1000
#define DOUBLE_CLICK_TIME 300
// 全局变量,用于记录按键状态
volatile uint32_t key1_state = 0;
volatile uint32_t key2_state = 0;
volatile uint32_t key3_state = 0;
volatile uint32_t key1_last_press_time = 0;
volatile uint32_t key2_last_press_time = 0;
volatile uint32_t key3_last_press_time = 0;
void LED_Init(void) {
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(LED_GPIO_CLK, ENABLE);
GPIO_InitStructure.GPIO_Pin = LED_RED_PIN | LED_GREEN_PIN | LED_BLUE_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(LED_GPIO_PORT, &GPIO_InitStructure);
}
void KEY_Init(void) {
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(KEY_GPIO_CLK, ENABLE);
GPIO_InitStructure.GPIO_Pin = KEY1_PIN | KEY2_PIN | KEY3_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; // 设置为上拉输入模式
GPIO_Init(KEY_GPIO_PORT, &GPIO_InitStructure);
// 初始化NVIC,配置中断优先级等
// ...
}
void LED_On(uint16_t pin) {
GPIO_SetBits(LED_GPIO_PORT, pin);
}
void LED_Off(uint16_t pin) {
GPIO_ResetBits(LED_GPIO_PORT, pin);
}
void Delay(uint32_t ms) {
// 延时函数,根据系统时钟进行调整
// ...
}
uint32_t GetSysTime(void) {
// 获取系统时间的函数,根据实际实现
// ...
}
void CheckKey1(void) {
if (GPIO_ReadInputDataBit(KEY_GPIO_PORT, KEY1_PIN) == Bit_RESET) {
uint32_t current_time = GetSysTime();
if (current_time - key1_last_press_time > DEBOUNCE_TIME) {
key1_state = 1;
key1_last_press_time = current_time;
}
} else {
key1_state = 0;
}
}
void CheckKey2(void) {
if (GPIO_ReadInputDataBit(KEY_GPIO_PORT, KEY2_PIN) == Bit_RESET) {
uint32_t current_time = GetSysTime();
if (current_time - key2_last_press_time > DEBOUNCE_TIME) {
key2_state = 1;
key2_last_press_time = current_time;
}
} else {
key2_state = 0;
}
}
void CheckKey3(void) {
if (GPIO_ReadInputDataBit(KEY_GPIO_PORT, KEY3_PIN) == Bit_RESET) {
uint32_t current_time = GetSysTime();
if (current_time - key3_last_press_time > DEBOUNCE_TIME) {
key3_state = 1;
key3_last_press_time = current_time;
}
} else {
key3_state = 0;
}
}
void main(void) {
LED_Init();
KEY_Init();
while (1) {
CheckKey1();
CheckKey2();
CheckKey3();
if (key1_state) {
LED_On(LED_RED_PIN);
} else {
LED_Off(LED_RED_PIN);
}
if (key2_state && (GetSysTime() - key2_last_press_time > LONG_PRESS_TIME)) {
LED_On(LED_GREEN_PIN);
} else {
LED_Off(LED_GREEN_PIN);
}
if (key3_state && (GetSysTime() - key3_last_press_time < DOUBLE
你觉得结果怎么样?